Project B18A1 Sleeper All Motor Underway!
Hey guys,
I know its been a while since I wrote anything but I have been slammed with getting our integra ready for shows with its custom paint theme (Will release more soon). We have been working with a ton of companies which I will list below along side of C-Tech Performance in Wyoming,MI www.c-techperformance.com on getting our motor for our Integra fully built and assembled. They are starting by balancing the whole rotating assembly and then boring the block .25 MM over.
The build plan goes as follows:
The Head:
Will have a stage 3 head job (thanks to www.performanceporting.com, these guys have the best prices and do grade A work!)
(Fully cleaned, gasket match ported intake, gasket match ported exhaust/polished, polished combustion chambers, gasket surfaces cleaned, Super tech valves, springs, retainers & valve seals thanks to www.supertechperformance.com, valve clearances checked, head milled .030, 3 angle valve job, Crower Stage 2 403 camshafts, Crower polished camgears thanks to www.crower.com, ARP Head & Main studs, Gates Racing timing and supertine belt thanks to www.gatesracing.com, Kamikaze Black 4-1 Header thanks to Kamikaze Performance.MSD Extreme Distributor Cap 82922,Rotor 8092,
Wire Set Extreme 8.5MM 35329,Thermotec Cool-Air Tube Heat Shield ,Cool-It Plug Wire Sleeves Red 4 Pack,Generation II Copper Header Wrap 1′x50′, & Starter Heat Shield, Golden Eagle Fuel Rail (Blue)
Parts we already have to transfer to the head:
K&N Short Ram
Skunk2 Pro Series Intake Manifold
RC Injectors
The Block:
Mahle 10.5 Pistons, rings, & pins
Bored over .25 MM
BILLET CROWERODS ACURA INTEGRA 1.8
Moroso Oil Pan thanks to www.certifiedracing.com
ACL Race main, rod and thrust bearings thanks to www.aclrace.com.au
Cometic Full Gasket kit C4388 & Head gasket C4238-030
ARP rod bolts thanks to www.certifiedracing.com
Fresh Hone
Block Completely hand cleaned and partially polished
Ralco RZ Single Belt Conversion Crank Pulley (Alternator only)
Aasco Lightweight Flywheel (8lb)
Exedy Stage 2 Clutch & Pressure Plate
Raxles Custom All Motor/Autocross SCCA Axles
Parts we have to transfer to block:
Full 2.25 Stainless steel exhaust
Vibrant Performance Muffler
LSD YS1 JDM XSi Trans
Fidanza Short Throw
& More
Partners Include:
SuperTech Performance www.supertechperformance.com
Certified Racinghttp://www.certified-racing.com/
Crower http://www.crower.com//
Gates Racing http://www.gatesracing.com/
Cometic http://www.cometic.com/
Performance Porting http://www.performanceporting.com/
Carquest
C-tech Performance http://www.c-techperformance.com/
Ralco RZ http://www.ralcorz.com/
Aasco Flywheels http://www.aascomotorsports.com/
Exedy Racing USA http://www.exedyusa.com/
Kamikaze http://www.kamikazeperformance.com/
MSD Ignition http://www.msdignition.com/
Thermo Tec http://www.thermotec.com/
Raxles Inc. http://www.raxles.com/
Stay tuned as we update on the process of the build!
You can continue to Project B18A1 Part 2
Leave a Reply
Tuner Maneuver Magazine - Muskegon,MI
